HMOR 422 D/3

HMOR 422 D/3

Apparatus for testing MOR

Modulus of Rupture (MOR) of refractory ceramics up to 1500°C

The modulus of rupture (MOR) is an important variable in the characterization of refractory materials. Determination of the maximum load at high temperatures is a property which, along with other thermophysical properties, is an important parameter for quality control and development of furnace linings.

The modulus of rupture is defined as the maximum stress a rectangular test piece of specific dimensions can withstand in a 3-point bending test until it breaks, expressed in N/mm2 or MPa.

The International Standard Test Method is described in ISO 5013;
test piece dimensions: 150 mm x 25 mm x 25 mm.

For determination of the modulus of rupture of refractories up to a temperature of 1500°C and a maximum load of 5000 N (60 N/mm2), NETZSCH offers the model 422 D/3. This model is designed for continuous testing with a 3-point bending device.
With optional devices for load and deformation measurement and/or constant deformation rate, additional information about the limits of elasticity and crack propagation in ceramic test pieces can be obtained.

The modulus of rupture model 422 E/4 is used to test small single test pieces in accordance with the 4-point load method with a distance between support edges of 40 mm. Inserting the test piece is simplified by the user-friendly split shell furnace (maximum temperature 1450°C). This unit uses a differential measuring system like that used by the RUL/CIC 421 for accurate determination of the test piece deformation.

Technika

Technika

(podlega zmianom)

  • Temperature range:
    RT to 1500°C (1450°C at HMOR 422 E/4)
  • Heating elements:
    SiC
  • Bending support:
    SiC
  • Load:
    1 N to 5000 N
    (2.0 to 12.5 N/s, switchable)
  • Bending measuring range:
    10000 µm (2500 µm at 422 E/4)
  • Temperature measurement:
    type S thermocouples
  • Sample dimensions:
    150 mm x 25 mm x 25 mm
    (45 mm x 4.5 mm x 3.5 mm at 422 E/4)
  • Bending mode:
    3-point (4-point at 422 E/4)
  • Atmospheres:
    air, static

The International Standard Test Method is described in ISO 5013;
test piece dimensions: 150 mm x 25 mm x 25 mm.

Oprogramowanie

Oprogramowanie

Both HMOR 422 D/3 and 422 E/4 run under Proteus® Software on Windows®. The Proteus® software contains all operations required to carry out measurements and, independent from that, for evaluation of the data, in part in MS EXCEL®. Through the combination of easy-to-understand menus and automated routines, a tool has been created that is extremely user-friendly and, at the same time, allows sophisticated analysis. The Proteus® software is licensed with the instrument and can of course be installed on other computer systems.

HMOR analysis features:

  • Start of the load increase, determination of the failure load
  • Storage of the test parameters and results
  • Transfer to MS EXCEL® for further analysis, graphic presentation and statistics
  • Determination of the test piece deformation (with the optional device for measurement of load and deformation)
  • Load-deformation diagram
  • Modulus of rupture calculation

You can use the following software with this product:

Proteus® Software

Akcesoria

Akcesoria

  • Vernier calipers for determination of the test piece dimensions, with online input into the Proteus® software
  • Interlayer disks
Literatura

Literatura

Plakat

Być może jesteś zainteresowany:

RUL/CIC 421 | Instrument badający ogniotrwałość pod obciążeniem i pełzanie przy ściskaniu

Seria instrumentów RUL/CIC 421 służąca do badania ogniotrwałości pod obciążeniem oraz przeprowadzenie tzw. próby pełzania przy ściskaniu. Konstrukcja tego urządzenia zapewnia długotrwałą i niezawodną pracę.

PCE 428 - Instrument do badania ogniotrwałości zwykłej

Określenie punktu mięknięcia materiałów ogniotrwałych jest tylko możliwe poprzez porównanie tego parametru z punktem mięknięcia laboratoryjnego stożka pirometrycznego. Próbki ogrzewa się w określonych warunkach razem ze wzorcowymi stożkami o znanej ogniotrwałości. PCE 428 umożliwia przeprowadzenie badań do 1700 °C.